TECNOFLON® TN 50A is a medium-low viscosity fluoroelastomer terpolymer. It does not contain curatives, therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve required properties. Thanks to its 68% of fluorine content, a good compromise between chemical resistance and compression set value is obtained. The careful distribution of molecular weights and medium-low viscosity maximize its performance in applications such as injection molding or extrusion where rheological properties are critical.
Some of the basic properties of Tecnoflon® TN 50A are:
Very good mold flow
Superior mold release
Good compression set
Good extrusion behavior
Tecnoflon® TN 50A can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers.
Tecnoflon® TN 50A can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.
Some of the basic properties of Tecnoflon® TN 50A are:
Very good mold flow
Superior mold release
Good compression set
Good extrusion behavior
Tecnoflon® TN 50A can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers.
Tecnoflon® TN 50A can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.
| Synonyms |
|---|
Fluorelastomer |
Markets
Processing Method
- Calendering
- Compounding
- Compression Molding
- Extrusion
- Injection Molding
- Transfer Molding
Chemical categories
| Chemical category | Chemical family | Chemical product |
|---|
Product Functions
- Low VOC
- Good Glycol Resistance
- Bio-Fuel Resistant
- Fuel Resistant
- Mineral/Synthetic Oil Resistant
- Hydrolysis Resistant
- Low Moisture Absorption
- Dielectric Properties
- Non Flammable
- Flame Retardant
- Low Compression Set
- Low CLTE
- UV Resistant
- Radiation (Gamma) Resistant
- Fast Cure
- Good Mold Release
- Good Processing Stability
- Crosslinkable
- Low Temperature Flexibility
- Good Thermal Stability
- High Heat Resistant
Format
| Physical form |
|---|
Slab |
Region of availability
- Not available in Africa & Middle East
- Asia Pacific
- Not available in Europe
- Not available in Latin America
- Not available in North America
TECNOFLON® TN 50A is a medium-low viscosity fluoroelastomer terpolymer. It does not contain curatives, therefore the proper levels of Tecnoflon® FOR M1 and Tecnoflon® FOR M2 must be added to achieve required properties. Thanks to its 68% of fluorine content, a good compromise between chemical resistance and compression set value is obtained. The careful distribution of molecular weights and medium-low viscosity maximize its performance in applications such as injection molding or extrusion where rheological properties are critical. Some of the basic properties of Tecnoflon® TN 50A are: - Very good mold flow - Superior mold release - Good compression set - Good extrusion behavior Tecnoflon® TN 50A can be used for compression, injection and transfer molding of shaft seals, valve stem seals, O-rings, gaskets and seals. This material can be combined with the cure system and other typical fluoroelastomer compounding ingredients. Mixing can be accomplished with two-roll mills or internal mixers. Tecnoflon® TN 50A can be extruded into hoses or profiles and can be calendered to make sheet stocks or belting. Finished goods can be produced by a variety of rubber processing methods.